[Remodeling 2008year] Fanuc 2 axis General purpose = NC table swing 300 center 600 grinding maximum OD:for φ405 grinding stone:300 for φ510 grinding stone:255 grinding maximum weight:130kg Standard grinding wheel width 25~75 ✤If there is a discrepancy between the specifications and the actual product, the actual product will prevail.

◆Controller: 160i-M ◆X-axis travel (mm): 300 ◆Y-axis travel (mm): 300 ◆Z-axis travel (mm): 320 ◆A-axis travel (mm): 360 ◆U-axis travel (mm): 200 ◆W-axis travel (mm): 0 to -180 ◆Spindle speed (min-1): 2000 to 8000 ◆Spindle speed range: S 4-digit direct command ◆Spindle taper: ISO #30 male taper ◆Spindle power (kW): 5.0/4.0 ◆Number of controlled axes: 6 ◆Number of simultaneously controlled axes: 6 ◆Lubricant tank capacity (L) ): 2 ◆Lubrication motor output (kW): 0.003 ◆Number of discharge nozzles: 6 ◆Grinding fluid tank capacity (L): 200 ◆Grinding fluid pump motor output (kW): 2.2 ◆Power supply specifications: 3-phase AC 200/220V±20% 50/60Hz ◆Power capacity (kVA): 23.2 ◆Machine height (mm): 2345 ◆Machine weight (kg): 2500 ✤If there are any discrepancies between the specifications and the actual product, the actual product will take precedence.

◆Controller: W21FAS-2 ◆Maximum workpiece dimensions (W * D * H): 1050 * 800 * 295 mm ◆Maximum workpiece weight: 1500 kg ◆Table dimensions: 780 * 630 mm ◆Axis travel (X * Y * Z): 500 * 350 * 300 mm ◆Table rapid feed speed: 1300 mm/min ◆Wire electrode diameter: 0.1 to 0.3 mm ◆Tapering device: Standard device ◆Axis travel (U * V): ±75 * ±75 mm ◆Maximum taper angle: 15° (for a plate thickness of 260 mm) (Note: This appears to be an error and should be omitted.) ◆Machine dimensions (W * D * H): 2013 * 2632 * 2100 mm ◆Weight: 3500 kg ◆Cutting fluid tank capacity: 740 L ◆Cutting fluid tank dimensions(W * D * H): 880 * 2085 * 1490 mm ◆Power supply unit (WFAS) ◆Power supply circuit: Transistor pulse circuit (stabilization circuit, AVR built-in) ◆Power supply dimensions (W * D * H): 550 * 600 * 1650 mm ✤In the event of any discrepancies between the specifications and the actual product, the actual product will take precedence.

◆Material Diameter: 51-type specifications: Φ8～Φ45mm (Φ51) H10～H38mm ◆Material Capacity: Φ10→30 pieces, Φ45→7 pieces, Φ51→6 pieces ◆Material Length: 4.0m ◆Remaining Material Disposal: Rearward extraction (remaining material length 70mm～500mm) ◆Feeding Speed: Forward maximum 350mm/sec, Reverse maximum 700mm/sec ◆Feeding Output: MAX 400N (40.8kgf) ◆Power Supply: AC200V 3PH 50/60Hz・2.0KVA ◆Air Source: 0.5～0.7Mpa (5～7kgf/cm²) ◆Oil Used: 4.0m → 65ℓ ◆Equipment Weight: 4.0m → 1,200kg ◆Body Length: 4,860 ◆Material Shelf Length: 4,030 ◆Leg Center Distance: 3,500 ◆Feed pipes are available in 42, 45, and 51 types as standard specifications; others are prepared to match the NC automatic lathe to which it is installed. ◆If the material diameter is larger than the maximum inner diameter of the finger chuck, please machine a step at the rear end of the material. ◆Setup replacement parts, options, and special specifications are handled separately. ◆Use the rotation speed according to the bending accuracy of the material. ✤In case of discrepancies between specifications and the actual product, the actual product will take precedence.

Wire diameter: 0.6 to 2.6 mm Maximum outer diameter: 40 mm Maximum leg length: 60 mm Spring index: 1:5 Number of control axes: 11 axes Machine dimensions: 1600 x 1900 x H1800 Total weight: 1630 kg Power supply: 220 V 50/60 Hz Rated output: 16.1 kw Power consumption: 42.5 A ✤ If there is a difference between the specifications and the actual product, the actual product will take precedence.

SOUL #7 chuck (3 craw) Swing on bed:360 Swing on the carriage:180 Between centers:500 Spindle taper hole:MT No.5 Spindle through hole:32mm 56-2500rpm Bed width x length:280 x 1350mm ✤If there is a discrepancy between the specifications and the actual product, the actual product will prevail.

Kitagawa chuck φ160 (6inch) Hole through:φ45 Bed swing:400 Bed length:1700 bed width:310 63~1600rpm electric motor:4P*3.7kw ✤If there is a discrepancy between the specifications and the actual product, the actual product will prevail.

◆ Swing above bed: 460 ◆ Distance from faceplate to 185 mm: 510 ◆ Swing of front and rear feed table: 240 ◆ Maximum center distance: 800 ◆ Center height from floor: 1000 ◆ Spindle through-hole diameter: 51 ◆ Spindle hole taper: M.T. No. 6 ◆ Center taper: M.T. No. 4 ◆ Speed ​​change: 8 stages ◆ Rotation speed: 50-1200 rpm ◆ Front and rear feed table travel distance: 280 ◆ Upper feed table travel distance: 140 ◆ Front and rear feed handle scale: 0.025 per graduation ◆ Upper feed table handle scale: 0.02 per increment ◆ Center travel distance: 150 ◆ Center taper: M.T. No. 4 ◆ Maximum carriage travel distance: 765 ◆ Feed rate: 32 types ◆ Bed length: 1850 ◆ Bed width: 400 ◆ Spindle drive: 3.7kW 4P ◆ Overall length: 2170 ◆ Overall width: 960 ◆ Overall height: 1230 ◆ Approximate weight: 1900 ✤ In the event of any discrepancies between the specifications and the actual product, the actual product will take precedence.

◆Swing above bed: 950mm ◆Swing above cross feed table: 630mm ◆Swing above cutoff: 1,200mm ◆Cutoff width from spindle end: 350mm ◆Maximum distance between centers: 7,000mm ◆Number of speed changes: 12 ◆Speed ​​range: 17-850rpm ◆Spindle end type: JIS A2-11 ◆Center taper: M.T. No. 5 ◆Spindle through-hole diameter: 105mm ◆Maximum cross feed table travel: 550mm ◆Tailstock diameter: 110mm ◆Tailstock tapered hole: M.T. No. 6 ◆Maximum tailstock travel: 260mm ◆Bed length: 9300mm ◆Bed width: 600mm ◆Main motor: 15kw, 4P ◆Machine length: 9590mm ◆Machine width * height: 1660 * 1570mm ✤If there are any discrepancies between the specifications and the actual product, the actual product will take precedence.

3 claws 6 inch chuck Bed swing:320 On the carriage swing:160 center:750～800 spindle hole throgh:35 125～3000rpm ✤If there is a discrepancy between the specifications and the actual product, the actual product will prevail.