- HOME
- Company Directory
- Japan
- W&N Co., Ltd.
- Product Inventory
SELLER PROFILE
W&N Co., Ltd.(W&N)Access: 1,458
1 ～ 15 of 15 POST
[MFR]MIROKU MACHINERY
[Model]MEG-1200-NC
[Year]1997
[Location]Niigata
[Price]
MIROKU MEG-1200-NC Gun Drill Machine --- Hole Diameter Capacity: 4 mm – 24 mm Max Drilling Depth: 1200 mm Spindle Speed Range: 580 – 5250 rpm Cutting Feed Speed: 0 – 500 mm/min Rapid Feed Speed: 5 m/min Table Size: 1000 × 1500 mm Table Load Capacity: 2000 kg Left/Right Stroke: 780 mm Vertical Stroke: 480 mm Main Coolant Tank: 850 L Auxiliary Tank: 350 L High-Pressure Pump: 105 kg/cm², 50 L/min Filter: 75 μ Chip Conveyor Capacity: 60 L/min Chip Discharge: 30 L/min Total Power Capacity: 14.5 kW (21 KVA) Required Floor Space: 6000 × 2800 mm Machine Weight: 8000 kg
[MFR]NAGASE INTEGREX
[Model]KNP-150S
[Year]1975
[Location]Niigata
[Price]
Electric Motor: 22 kw Pressing Capacity: 150 ton Die Cushion: 75 ton Normal Pressure: 212kg/㎠ Cushion Pressure: 235kg/㎠ Stroke: 600 mm Cushion Stroke: 225 mm
[MFR]VORONEZH
[Model]KA9536
[Year]1979
[Location]Niigata
[Price]
VORONEZH 400 ton Trimming Press --- Nominal Force: 4000 kn Side Stroke: 400 mm Stroke per minute: 25 Adjustment: 470 mm Adjustment Stroke: 160 mm Bed Dimensions: 1000 x 1000 mm Slide Dimensions: 800 x 800 mm Bolster Plate Thickness: 160 mm
[MFR]SATO TEKKO
[Model]SLP-1500-140-130
[Year]1997
[Location]Niigata
[Price]
Capacity: 1500 ton Rated Capacity Position: 25 mm (Above Bottom Dead Center) Stroke Length: 350 mm Continuous Stroke Rate: 15~25 spm Single Stroke Rate: 8 spm (at continuous 25 spm) Slide Adjustment: 150 mm Die Height: 850 mm (Stroke Down, Adjustment Up) Slide Size: (L × W) 1400 × 1300 mm Bolster Size: (L × W) 1400 × 1300 mm Required Air Pressure: 5 kgf/cm² Press Main Drive DC Motor, 150 kW
[MFR]AIDA ENGINEERING
[Model]PS-20
[Year]
[Location]Niigata
[Price]
AIDA ENGINEERING PS-20 Forging Press --- Capacity: 200 Ton Stroke Length: 200 mm Stroke Speed: 40 SPM Bolster Size: 900 × 900 mm Slide Size: 750 × 750 mm Slide Adjustment: 100 mm Bolster Thickness: 100 × 50 mm Required Air Pressure: 5 kg/cm²
[MFR]AIDA ENGINEERING
[Model]PS-30
[Year]
[Location]Niigata
[Price]
AIDA PS-30 Forging Press --- Capacity: 300 Ton Stroke Length: 250 mm Stroke Speed: 20~40 SPM Bolster Size: 900 × 1100 mm Slide Size: 900 × 900 mm Slide Adjustment: 125 mm Bolster Thickness: 225 mm Required Air Pressure: 5 kg/cm²
[MFR]OTANI MACHINERY
[Model]DIE MAX 100E
[Year]
[Location]Niigata
[Price]
OTANI DIE-MAX 100E --- SPECIFICATIONS: Capacity 2 ton Standard Lower Die Weight 2,690 kg Standard Upper Die Weight 600 kg Minimum Safe Die Height 350 mm Maximum Stroke 1,200 mm Guide Clearance 630 mm Cylinder Bore Diameter 430 mm Piston Rod Diameter 160 mm Ram Bottom Size 630 (W) × 650 (L) mm Sow Block Top Surface Size 700 (W) × 750 (L) mm Impact Energy 9,900 kg·m Air Inlet Connection 125A (5B) Air Exhaust Connection 125A (5B) Height from Floor Level (F.L.) Approx. 5,435 mm Overall Machine Height 6,445 mm Height to Remove Piston Rod (from F.L.) 7,850 mm Required Air Compressor Capacity over 150 kW Maximum Operating Pressure 0.69 MPa (7 kg/cm²) --- CURRENT CONDITIONS: The machine is being offered for sale due to a reduction in production of the applicable product. The frame and cylinder have been replaced and repaired. Reinforcement repairs using steel backing plates have been carried out on the cracked areas on both the front and rear sides of the cylinder. The anvil knockout mechanism has currently been filled in (disabled). There is a possibility that cracks exist inside the knockout section.
[MFR]OTANI MACHINERY
[Model]Die-Max 200
[Year]2017
[Location]Niigata
[Price]
OTANI Die-Max 200 Hammer --- Standard Lower Die Weight: 2,690 kg Standard Upper Die Weight: 600 kg Minimum Safe Die Height: 350 mm Maximum Stroke: 1,200 mm Guide Clearance: 630 mm Cylinder Bore Diameter: 430 mm Piston Rod Diameter: 160 mm Ram Bottom Size: 630 (W) × 650 (L) mm Sow Block Top Surface Size: 700 (W) × 750 (L) mm Impact Energy: 9,900 kg·m Air Inlet Connection: 125A Air Exhaust Connection: 125A Height from Floor Level (F.L.): Approx. 5,435 mm Overall Machine Height: 6,445 mm Required Air Compressor Capacity: Over 150 kW Maximum Operating Pressure: 0.69 MPa (7 kg/cm²)
[MFR]OTANI MACHINERY
[Model]New Max 130
[Year]
[Location]Niigata
[Price]
NOTES: Only the anvil, cylinder, and frame are available. All other components will need to be newly manufactured. Manufacturing drawings can be provided.
[MFR]MANYO
[Model]DLB300MN
[Year]
[Location]Niigata
[Price]
Capacity: 300 ton The machine is currently undergoing a complete overhaul
[MFR]MANYO
[Model]DLB450MN
[Year]
[Location]Niigata
[Price]
Capacity: 450 ton The machine is currently undergoing a complete overhaul
[MFR]MITSUI ENGINEERING ＆ SHIPBUILDING
[Model]
[Year]2009
[Location]Niigata
[Price]
MITSUI E&S 2000 kw Electric Induction Heater --- Capacity: 1600 kw (Actual output equivalent to 2000 kw) Heating Coils: Φ170 / Φ220 Switchgear: 60 Hz, 6600 V (High Voltage) Power Transformer: 60 Hz, 6600 V / 2500 kVA Intermediate Frequency Power Supply: 2000 kw, 500 Hz Integrated Control Cabinet Standalone Control Box Load Push Rod Mechanism Usage time: Used approximately 10 times, only for trial run and prototype production
[MFR]UCHINO
[Model]USH-HVH-3UB
[Year]2003
[Location]Niigata
[Price]
Uchino 550 kw Induction Heater --- Voltage: 50 Hz, 6600 V Circuit Breaker Type: VCB Rating: 7.2 kV, 600 A, 12.5 kA (at 7.2 kV) Operation: Manual spring-operated Base Plate provided Dust-proof type
[MFR]HITACHI INDUSTRIAL EQUIPMENT SYSTEMS
[Model]OSP-240S6WT
[Year]2019
[Location]Niigata
[Price]
Hitachi Screw Compressor 240 kw --- Model: OSP-240S6WT Output: 240 kw Voltage: 6600 V (high voltage) Frequency: 60 Hz Usage time: 5,230 hours
