- HOME
- Select Manufacturer
- DAINICHI KINZOKU KOGYO
DAINICHI KINZOKU KOGYO Product List
1 ～ 11 of 11 POST
[MFR]DAINICHI
[Model]BX105-150
[Year]1998
【❖Take a look at our video!❖】 F18T 18"Hydraulic chuck (solid) Hole through:φ320 Bed Swing:φ1050 cross slide swing 900 Work length:1500 Tail cup XZ:510*1500 2～500min-1 V12 ✤If there is a discrepancy between the specifications and the actual product, the actual product will prevail.
[MFR]DAINICHI KINZOKU KOGYO
[Model]DLX75B×150
[Year]2001
FANUC-20iTA Swing over bed: 750 Distance between centers: 150 S:X450*Z157 Through-hole: ø245 5-jaw chuck Cutting tools (H4 tool rest): 4 Centering table: MT5 Run-out stop
[MFR]DAINICHI KINZOKU KOGYO
[Model]DHK75*150
[Year]1983
[MFR]DAINICHI KINZOKU KOGYO
[Model]DL53×100
[Year]1996
F-20T φ530*1000 Cross φ300 0.001 KITAGAWA 3jaw chuck JN09T Work light Front chip cover Rear chip cover RS232C
[MFR]DAINICHI KINZOKU KOGYO
[Model]DL53×100
[Year]1997
F-20T φ530*1000 Cross φ300 0.001 KITAGAWA 3jaw chuck JN10T Steady Rest Coolant pump Rear chip cover RS232C
[MFR]DAINICHI KINZOKU KOGYO
[Model]MG75×140
[Year]2021
FANUC 32i-B 20inch 4jaw Independent chuck 3~1150Rpm Max machining dia φ750 Tool rest H6 S: 380*1530 Swing Over carriage 460 Spindle bore φ85 Chip Conveyer Machines covered by the Guaranteed Uptime Service (option)
[MFR]DAINICHI KINZOKU KOGYO
[Model]DLG-SH63-200
[Year]1985
◆Swing above bed: 630 ◆Center distance: 2000 ◆Swing above cut-off: 900 ◆Swing above carriage: 400 ◆Bed length: 3400 ◆Bed width: 425 ◆Spindle through hole diameter: 54 ◆Spindle taper hole: Metric taper #60 ◆Spindle nose: Short taper ASA A-1-6” ◆Spindle speed: 14 stages 18-1600 rpm (7.5kW or 11kW), 14 stages 125-1120 rpm (7.5kW), 14 stages 9-800/min (5.5kW) ◆Lead screw diameter and pitch: 40mmΦ, 6mm pitch ◆Left/right feed: 64 stages 0.062-14mm/spindle revolution ◆Front/rear feed: 64 stages 0.031-7mm/1 spindle revolution ◆Inch thread cutting: 37 steps, 56-1 teeth/25.4mm ◆Metric thread cutting: 31 steps, 0.5-28mm pitch ◆Modular thread cutting: 21 steps, 0.25-7πmm pitch ◆D.P. thread cutting: 27 steps, 56-4 teeth/25.4π ◆Motor: A.C., 3 phase, 7.5kW ◆Estimated weight: 2800 ✤If there is a difference between the specifications and the actual product, the actual product will take precedence.
[MFR]DAINICHI KINZOKU KOGYO
[Model]DL65×250
[Year]1997
Fanuc-20T 4-jaw independent chuck: 17 inches Center:2,500mm swing over bed:650mm 1,120rpm X380 Z2,570mm Fixed steady rest: 1 (dia200mm)
[MFR]DAINICHI KINZOKU KOGYO
[Model]DL53ⅹ100
[Year]1996
If you have any questions about specifications, feel free to contact me. I will share a PDF file with folks. Thank you .
